copy protect

Thursday, December 14, 2017

Folder progress

Got some time to work on the blade, I'm surprised at how soft the steel is.  It bends before it breaks, and can be worked with a file relatively easily.  I looked up heat treating stainless on the web, and found some surprises.  Older 300 series SS does not react to hardening and tempering, but it will work harden- hammer on it it gets harder.  Surprise!  Newer 400 series SS can be hardened and tempered, the site I found lists max hardness at 60 on the Brinell scale, whatever that means.  I can't find a conversion chart for Brinell to RC.



Here's the rough ground blade, it's close to what I want, though I might take a bit more off the width.  The shape of the blade and the length were dictated by my decision to use the original nail nick.  I'll save reinventing the nick for a later knife.  At this point the edge is square, about 1/32 inch thick- I haven't touched the bevels yet.


Here's a view I've never seen- interesting how the pieces nest together inside the knife, I think.  I temporarily assembled the knife on one side to look at how the open knife edge related to the handle- I like them to be (mostly) in line- and to make sure I didn't end up with the point of the blade no covered by the liners.

I'm debating about whether to try hardening and tempering the blade.  I'm used to harder in my carbon steel blades, on the other hand, I should test the factory blade for edge holding.

Stay tuned.


Tuesday, December 12, 2017

Might have found the ONE

I've made a few hundred knives, all fixed blades, but have regularly dreamed of a folding whittler.  there are dozens of knives out there called whittlers, only one or two have blade(s) shaped the way I like, and of those they are either too pricey for my pocket or have not-so-good reviews from people I trust. 

I've bought a bunch of folders over the years, always intending to modify them to suit but have never changed a  single one.  There's more than a couple reasons for that.

First is the fear of damaging the pivots, or blade, or having the damn thing fold up on my fingers while grinding and damage me.  One solution would be to dismantle the knife, modify and re-assemble.  Little more work than I want to undertake, for a knife I'm not sure I'll like when I'm done.

Second is I assumed a grinder was the only way to reshape a blade; add overheating the blade to the list of fears above.

Third, I've tried to make a nail nick, which some mods will require, but have not been successful yet.  It would be a shame to let an ugly nail nick live on a nicely modded knife.

Reason 4, I've believed stainless steel blades to be inferior to high carbon, but all the HC folders were in the ozone price range.  Not gonna spend that much on a knife with a 50% chance of ruining it.

Last reason is darnit, I just like some of them like they are.  Couple of them have become regular carries for me.

Changed My Mind

A recent exchange on the WCI forum opened my eyes, and a stroke of luck may let this project move forward.  Couple of cronies on the forum suggested using files to reshape the blades.  Not sure why I didn't think of that, but it suits me just fine.  No grinding waste to breathe in, damage to the knife (and my fingers) can be avoided.  It'll take a little longer, but it'll be quieter too.

Same discussion touched on the differences, or lack thereof, between HC steel and modern SS.  Two guys say they have compared steels head to head, and found no difference in sharpening or edge retention (they mentioned 440 stainless).  That's impressive.  I'm willing to give it a try.

Then I got lucky, and found this:


Rough Rider makes 5 or 6 knife kits, all parts included, assembly required.  I picked this one- RRCS5- for two reasons:  the barlow configuration with the (very) large bolster, and the lockback.  I consider a locking blade as a Darn Good Idea.  You can see I've sketched the blade rework in, I get to keep the nail nick on this first one.  Working the blade on a dismantled knife seems perfect.  No bolster on the back made me think I could reshape that end, but now that I hold one in my hands I see the rivet holes are going to limit that.  I've emailed RR asking if the blade is 440, as it is not marked and that info is not included in their description.  To date no response.

Stay tuned I will update when and if work progresses.















Monday, December 11, 2017

2017 Ornie Exchange

I participated in the Christmas Ornament Exchange on the Woodcarving Illustrated forum again this year.  Last time was in 2010, not sure why I haven't done it more, its a lot of fun.  8 signed up this year, including one we send to the magazine as way of thanks for hosting the forum for us.  I made little elephants with Santa hats, based on the baby elephant in Tom Hindes book 20-Minute Whittling Projects.  They took me more than 20 minutes each, I never am as fast as the authors.  Thanks for a great book, Tom.  Tom's a good whittler, and a good teacher too IMO.  If you get a chance to pick up his book, I recommend it.

I thought I'd run through some of the steps I take on a project like this, starting with a pic of a finished elepehant:



And before paint:


When planning a whittling, I like to think about what makes the subject unique, or what features I need to steer the viewer's imagination in the right direction.  Since I don't 'do' reality, imagination is required when looking at my 'work'.

Thats an easy list to make when the subject is an elephant- trunk of course, big ears (African ears are large, Indian ears not so much), tree trunk legs, big round body & butt, and a ridiculoulsy small tail.  That's a long list, covering the animal from tip to bottom.  jSometimes you only get one thing.

Once I've thought about the features I want, I shoot for a full size sketch/pattern on whatever paper is nearby.  This one was easy-  Tom included a nice little line drawing in his book, an easy starting place.  Had to think a little about what makes a Santa hat too- fur brim, ball on top, red color- easy stuff there too.  The first pattern looked like this:


I started to think about grain direction and actually whittling this little guy, and it didn't ake long to realize the kink in the hat was going to be a nightmare.  Grain had to go the long way along the trunk, making that hook in the hat tough or impossible to complete without breaking.  NOTE: I use a knife only, which imposes restrictions on the work; using a dremel or similar power carver would have make the bent hat possible.

So before I even cut one out of wood I modified the pattern:

Scissor snip

I used this pattern to trace one on wood and started whittling.  I'm likely to make some changes after the first.  That is one reason why I like to do repeats- the whittling evolves as I go, I love that process.
Once I've done the first, and made any changes, the next thing is a more durable pattern:


I use card stock, and include notes on the size blank I need for each.  this pattern will hang out in the shop near the saw.

I actually made another change after this- the space between the front and back legs morphed from a U-shape to a single saw cut.  

I can separate the legs with a few cuts that extend up into the belly.

There's a few things on my elephant that depart from reality.  Elephants actually have quite a long bit of belly between the front & back legs- mine have none. I didn't put eyes on them either.  I made up the transition from face to trunk, and varied it from one to the next.  I found a couple I preferred, but can guarantee none of them are anatomically correct.  I don't mind any of that- none if it detracts from creating the impression of an elephant.